RF Splitters, Filters, Accessories

V902: Satellite Signal Diplexer

Brand: 
Channel Plus

The Model V902 Satellite Signal Diplexer functions as a wide bandwidth splitter/combiner. Using the Model V902 as a combiner allows lower frequency signals from an off-air antenna or modulator and higher frequency signals from a satellite dish LNB to be combined onto one coax cable. A second Model V902 used as a splitter at the DSS receiver/TV location will separate the signals back onto two coax cables.

C-BCK: Cable Box Combiner Kit

Brand: 
Channel Plus

When a CATV converter box is required at each television location but does not have unused channels available for modulated ChannelPlus channels, a cable box combiner kit, Model C-BCK is needed. The Model C-BCK Cable Box Combiner Kit allows the CATV box to be tuned to all normal CATV channels; these are viewed when the television is tuned to channel 3. The modulated channels are viewed when the television is tuned to the ChannelPlus modulator channel numbers. The Model C-BCK cable box combiner kit includes a high-pass filter, two 2-way splitter/combiners and two 6-inch coaxial cables.

TC-200A: Tilt Compensator

Brand: 
Channel Plus

The Model TC-200A Tilt Compensator is an in-line filter designed to create an attenuation loss equal and opposite to cable loss.

2507-10: 75-ohm Terminator

Brand: 
Channel Plus

The Model 2507-10 75-ohm Terminator (10-pack) provides a 75-ohm load that can be used on unused splitter output ports in order to maintain uniform signal levels.

Do not use terminators on unused distribution amplifier outputs.

Features

  • 10 piece bulk pack
  • Terminates unused splitter outputs with a balanced 75-ohm load
  • Type F male connector

2506-10: 6dB In-line Attenuator

Brand: 
Channel Plus

ChannelPlus in-line attenuators can be inserted in coaxial cable feeds to reduce signal amplitude levels. The Model 2506-10 6dB In-line Attenuator (10-pack) provides a 6 dB insertion loss, and the Model 2503-10 provides a 3 dB insertion loss. Combinations of 2506s and 2503s may be used together to create attenuators with greater insertion loss. These attenuators provide a better, more permanent solution over using a variable attenuator.

Features

  • 10 piece bulk pack
  • Reduces signal strength 6 dB
  • Type F barrel connector

2503-10: 3dB In-line Attenuator

Brand: 
Channel Plus

ChannelPlus in-line attenuators can be inserted in coaxial cable feeds to reduce signal amplitude levels. The Model 2503-10 3dB In-line Attenuator (10-pack) provides a 3 dB insertion loss, and the Model 2506-10 provides a 6 dB insertion loss. Combinations of 2503s and 2506s may be used together to create attenuators with greater insertion loss. These attenuators provide a better, more permanent solution over using a variable attenuator.

Features

  • 10 piece bulk pack
  • Reduces signal strength 3 dB
  • Type F barrel connector

2501-10: Blocking Capacitor

Brand: 
Channel Plus

The Model 2501-10 Blocking Capacitor (10-pack) is used in systems where DC and/or infrared control pulses are present on the coaxial cable. When such signals are not wanted or might be shorted out by downstream video products, a Model 2501-10 blocking cap can be inserted in an individual coaxial cable feed. The capacitor serves like an open circuit to DC and low frequency IR control signals, yet passes all RF signals on.

Example: Using a 12-volt IR system and not using Model 2100A wall plates at all coax drops, insert a Model 2501-10 on the end of the coax.

NF-471: Notch Filter

Brand: 
Channel Plus

The Model NF-471 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-471 filters out channels to make room for modulated channels. In addition, the NF-471 blocks the modulated signals from being broadcast back into the coax. The NF-471 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

NF-470: Notch Filter

Brand: 
Channel Plus

The Model NF-470 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-470 filters out channels to make room for modulated channels. In addition, the NF-470 blocks the modulated signals from being broadcast back into the coax. The NF-470 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

NF-469: Notch Filter

Brand: 
HAI

The Model NF-469 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-469 filters out channels to make room for modulated channels. In addition, the NF-469 blocks the modulated signals from being broadcast back into the coax. The NF-469 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

Syndicate content